Home › CDL Practice Tests › Florida › Air Brakes
Florida CDL Air Brakes Practice Test
Practice the full Air Brakes question set for the Florida CDL knowledge test. Every question comes with an instant explanation and its manual topic, so you learn the rule behind the answer instead of memorizing letters.
Free and unlimited. Every answer is explained, and your progress is saved only in your browser — no account needed.
How it works
Answer one question at a time. You will see immediately whether you were right, plus a short explanation and the manual topic for every question. At the end you get your score and can re-drill only the questions you missed.
250 questions · Topics: Dual Air Brake System & Components, Air Compressor, Governor & Reservoirs, Safety Valve & Low-Pressure Warning, Leakage Rate Standards & Air Tests, Spring Brakes, Parking & Emergency Brakes, Brake Inspection Steps & Defects, Slack Adjusters & Pushrod Stroke, Brake Fade, Heat & Downgrade Braking, ABS & Anti-Skid, Air Tank Draining, Alcohol Evaporators & Dryers, Tractor Protection Valve, Trailer Brakes & Stab Braking.
Question 1 of 250Score: 0
Your result
About this practice test
This set drills the Air Brakes topics from the official CDL manual: dual air brake system & components, air compressor, governor & reservoirs, safety valve & low-pressure warning, leakage rate standards & air tests, spring brakes, parking & emergency brakes, brake inspection steps & defects, slack adjusters & pushrod stroke, brake fade, heat & downgrade braking, abs & anti-skid, air tank draining, alcohol evaporators & dryers, tractor protection valve, trailer brakes & stab braking. The real Florida test is given by the Florida Department of Highway Safety and Motor Vehicles (DHSMV); format and passing scores are summarized on the Florida CDL hub page.
When this set feels easy, switch to the Exam Simulator for a timed, no-feedback run, or review with flashcards.
Frequently asked questions
How many questions are on the Florida Air Brakes test?
The Air Brakes test is typically about 25 multiple-choice questions in most states.
What score do I need to pass?
Most states, including the typical Florida standard, require about 80% correct on CDL knowledge tests. Confirm the current rule in the official manual.
Are these the actual test questions?
No. These are original practice questions written from the same public manual topics the real test covers. They are designed to teach the material, not to reproduce the exam.
Browse all 250 questions in this set
- What is the main purpose of a dual air brake system on a modern truck?
- In a dual air brake system, what does the primary system typically control?
- In a dual air brake system, what does the secondary system typically control?
- How can a driver monitor a dual air brake system while driving?
- If one circuit of a dual air brake system fails completely, what should the driver expect?
- What part applies the service brakes when air pressure is delivered to it at each wheel?
- What is the job of the slack adjuster in an S-cam air brake?
- What happens inside an S-cam drum brake when the S-cam rotates?
- What does the foot valve (treadle valve) do when the driver presses the brake pedal?
- Why do large trucks use a relay valve for the rear service brakes?
- What is brake lag in an air brake system?
- Which component keeps dirt and moisture from doing the most harm by removing water and oil from compressed air before it reaches the tanks?
- What are the flexible air hoses and lines between the tractor and trailer commonly connected with?
- Which trailer air line carries the control signal that tells the trailer brakes how hard to apply?
- Which trailer air line keeps the trailer air tanks charged and also triggers trailer emergency braking if it loses pressure?
- What does a quick-release valve do in an air brake system?
- What is the purpose of the one-way check valves between air tanks in a dual system?
- A driver notices the primary gauge falling while the secondary gauge stays normal. What does this most likely indicate?
- What type of foundation brake is most common on heavy trucks in North America?
- Why must brake chambers of different sizes or slack adjusters of different lengths not be mixed carelessly on the same axle?
- What should a driver check about air hoses during a pre-trip inspection?
- What does the application pressure gauge, when fitted, tell the driver?
- In an air disc brake, what creates the clamping force on the rotor instead of an S-cam spreading shoes?
- What happens if a brake lining becomes soaked with oil or grease?
- Why are air brakes preferred over hydraulic brakes for very heavy combination vehicles?
- What is the role of the brake drum in an S-cam system?
- During inspection, a pushrod stroke is found to be beyond the allowable limit for its chamber size. What does this mean?
- What powers the movement that ultimately applies every service brake in a full air system?
- If the air pressure in both dual circuits drops very low, what additional system is designed to stop the vehicle automatically?
- Why should a driver never disconnect the gladhand lines while the trailer supply pressure is still high without first setting the brakes and following proper uncoupling steps?
- What drives the air compressor on most heavy trucks?
- What does the air governor do?
- At about what pressure does the governor cut out and stop the compressor from pumping on a typical system?
- At about what pressure does the governor cut in and restart the compressor pumping?
- If tank pressure keeps rising well past governor cut-out toward 150 psi, what is the most likely fault?
- What is the purpose of the air reservoirs (tanks)?
- Why must air tanks be drained regularly, ideally daily?
- In cold weather, what is the specific danger of water left in the air tanks and lines?
- What does an alcohol evaporator do on vehicles equipped with one?
- During the engine inspection, how should the driver check a belt-driven compressor or other engine belts?
- About how long should it take for air pressure to build from 85 to 100 psi at normal operating RPM during a proper test?
- What is the correct way to drain air tanks that have manual drain valves?
- What happens to stored air capacity if a tank is partly filled with water and oil sludge?
- Which tank usually collects the most moisture and should be drained first?
- A compressor passes excessive oil into the air system. What is the likely long-term result if it is ignored?
- When checking air build-up at start-up, the pressure rises very slowly and never reaches cut-out. What should the driver do?
- What does it mean when the compressor cuts out normally at the top of the range?
- Why should a driver let a cold engine idle and watch the gauges before moving after start-up?
- What is the function of the air dryer purge that is heard as a brief blast of air when the compressor reaches cut-out?
- If the compressor drive belt breaks while driving, what will happen to the air system?
- At about what pressure does the safety valve on an air tank normally open to vent excess pressure?
- What is the job of the safety valve?
- If the safety valve is popping off repeatedly during a trip, what should the driver do?
- Before air pressure falls below what value must the low air pressure warning activate?
- What forms can the low air pressure warning take?
- The low air pressure warning comes on while you are driving. What is the correct response?
- How do you test the low air pressure warning during a pre-trip inspection?
- During the low-pressure warning test, the gauge falls to 50 psi with no light or buzzer. What does this mean?
- Why is 60 psi such an important threshold in an air brake system?
- What is a wig wag low-pressure warning device?
- After start-up, the low-pressure warning stays on even though the gauge shows 125 psi. What is the best interpretation?
- What should happen to the low-pressure warning as air builds during a proper start-up?
- Why must the driver never silence or disable a low-pressure buzzer that keeps sounding at low pressure?
- Which condition would cause BOTH the low-pressure warning to activate and, if ignored, the spring brakes to eventually apply?
- How can a driver distinguish normal governor cut-out from a safety valve event?
- During an inspection, at what point in the fanning test should spring brake knobs be expected to pop out on many vehicles?
- What does a safety valve that is stuck closed create a risk of?
- A driver hears air venting from a tank valve at 150 psi and the gauge is still climbing. What two devices have effectively failed or been exceeded?
- Why do inspectors check the low-pressure warning on every pre-trip rather than trusting it from the last trip?
- What is the safest place in the pressure range to make a planned stop after a low-pressure warning?
- For the static leakage test, what are the starting conditions?
- With the engine off and brakes released, what is the maximum allowable leakage rate for a single vehicle?
- With the engine off and brakes released, what is the maximum allowable leakage rate for a combination vehicle?
- For the applied-brake leakage test, what does the driver do after making a full brake application?
- With the brakes fully applied and the engine off, what is the maximum allowable leakage for a single vehicle?
- With the brakes fully applied and the engine off, what is the maximum allowable leakage for a combination vehicle?
- A combination vehicle loses 5 psi in one minute during the applied-brake test. What is the correct conclusion?
- Why must the engine be off during leakage tests?
- During the applied test, pressure drops quickly at first and then steadies. How should that initial drop be treated?
- What is the correct order of the standard air brake inspection tests?
- How is the governor cut-out pressure checked during the test sequence?
- Why is fanning the brakes (rapidly pumping the pedal) dangerous when air pressure is already low?
- A single vehicle loses 3 psi in one minute with the brakes released. Does it meet the standard?
- A combination vehicle loses 2 psi in one minute with the brakes released. Does it meet the standard?
- What additional check follows the leakage tests if pressure loss is near the limit but no leak is obvious?
- Why do combination vehicles get a slightly higher allowable leakage rate than single vehicles?
- What should a driver do before timing a leakage test to get an honest result?
- If air pressure builds normally but falls rapidly whenever the service brakes are applied repeatedly in traffic, what is a likely cause?
- What does the brake test at the start of a trip, rolling at about 5 mph, check that gauge tests cannot?
- During the pop-out test, after fanning the brakes down, what pressures tell the full story of a healthy system?
- A truck fails the build-up test, taking far longer than 45 seconds to go from 85 to 100 psi. What does that suggest?
- Why should leakage be rechecked after hooking to a trailer that was not part of the tractor's earlier test?
- What is the risk of passing a leakage test in warm weather and assuming the same truck is fine in freezing weather?
- How long is each leakage measurement timed for the standard test?
- If the gauges disagree sharply with each other during a dual-system leakage test, what should the driver suspect?
- What holds the spring brakes in the released (off) position during normal driving?
- What applies the spring brakes when they engage?
- In what pressure range do spring brakes become fully effective as air pressure falls?
- What are the two jobs of spring brakes?
- How does the driver normally set the parking brakes on an air brake vehicle?
- What are the colors and shapes of the standard parking control knobs in a combination vehicle cab?
- What does pushing in the red trailer air supply knob do?
- What is the job of the tractor protection valve?
- At about what pressure range will the tractor protection valve close and the trailer supply knob pop out during an air loss?
- If a trailer breaks away from the tractor on the road, what happens to the trailer's brakes?
- Why should spring brakes never be mechanically caged or backed off and left that way for normal driving?
- What is the danger of applying the parking (spring) brakes when the drums are extremely hot after a long descent?
- Why should the parking brakes not be relied on alone when parking a trailer on a grade without the tractor?
- What must a driver do before releasing the spring brakes after a cold start?
- A driver parks and pulls both knobs out, but the vehicle slowly rolls. What is a possible cause to report?
- How can a driver test that the parking brakes hold during an inspection?
- What is a modulated (spring brake) control valve on some older vehicles used for?
- In a total service brake air loss at speed, what is the driver's best emergency stopping strategy?
- Why can wet spring brakes be a problem if the parking brakes are set overnight in freezing weather?
- After parking for the night in very cold weather with wet brakes, what is the recommended practice when conditions allow?
- What happens if a driver tries to compound the brakes by making a full service application while the spring brakes are already applied?
- What device on many systems prevents compounding damage automatically?
- When uncoupling a trailer, why is the trailer air supply knob pulled (or parking set) before disconnecting the gladhands?
- What should the driver do if the yellow parking knob pops out on its own while driving?
- How do spring brakes differ from the service brakes in everyday use?
- Why must a driver chock wheels or otherwise secure the vehicle before working under it with the spring brakes released for service?
- What is the correct action if the spring brakes drag and will not fully release after the knobs are pushed in?
- During the inspection pop-out test, the trailer supply knob does not pop as pressure falls through 30 psi. What does this indicate?
- What energy source makes spring brakes trustworthy even after a vehicle sits parked for a long time with all air leaked away?
- When parking a bobtail tractor (no trailer) on a grade, what secures it?
- During a pre-trip inspection of an air brake system, what is the main purpose of checking each brake component before driving?
- When you inspect rubber air hoses for the service brakes, which condition should be reported as a defect?
- What should brake drums (or discs) be checked for during an inspection?
- Which finding on brake linings makes the brake unsafe until it is corrected?
- How do you test the low air pressure warning device during a pre-trip check?
- After building air pressure to governor cut-out, turning the engine off, and making a full brake application, what does a continuing drop on the air gauge after the initial drop tell you?
- What are you checking when you test the air compressor governor cut-out pressure?
- How is the spring (parking) brake test commonly performed during an air brake check?
- What is the correct way to test the service brakes after starting a trip or inspection?
- How should you check the parking brake during an inspection?
- What should you look for when inspecting brake chambers and their mounting?
- During an inspection you hear a steady hiss near a brake valve after the brakes are released. What does that most likely indicate?
- If a vehicle's engine-driven air compressor has a drive belt, what should that belt be checked for?
- Why are two air pressure gauges (or a dual gauge) checked against each other during an inspection?
- What condition of a brake hose connection at a glad hand or fitting is a defect?
- You find grease and oil inside a wheel around the brake drum area. Why is this treated as a serious brake defect?
- What should you check about the brake pedal and its action during a cab inspection?
- Which crack or defect in a brake drum is a reason to take the vehicle out of service?
- During a pre-trip air brake check with the engine off and the brakes applied, you hear air hissing steadily from one brake chamber. What does this most likely mean, and what must you do?
- During your en route checks, why should you pay attention to how the brakes feel and whether a wheel or hub is unusually hot?
- When inspecting S-cam brakes, what should you confirm about the camshaft, rollers, and return springs where they are visible?
- What is a sign during inspection that a service brake chamber diaphragm may be leaking?
- Why must a cracked or badly bent brake component, such as a chamber bracket or torque arm, not be ignored?
- What should you do if one brake on an axle is clearly doing much less work than the other, shown by a much cooler drum after a stop?
- During the inspection of disc brakes, which condition should be reported?
- Why do you check that brake linings are not wearing unevenly from one end of the shoe to the other?
- What is the safest action if your pre-trip brake test shows the vehicle does not stop as it should at low speed?
- When checking air pressure build-up time, what problem is suggested if pressure rises very slowly from low pressure to the normal range?
- What should be verified about the tractor's gauges and warning lights as part of the in-cab brake check?
- If you find a brake that is dragging after the pedal is released during inspection, what is the likely effect if it is driven that way?
- What does a slack adjuster do in an S-cam air brake?
- How do you measure pushrod stroke (applied stroke) when checking brake adjustment?
- For many common brake chambers with a manual slack adjuster, about what pushrod stroke is the commonly cited maximum limit?
- What happens when pushrod stroke becomes excessive?
- When checking slack by hand, how much free movement at the slack adjuster suggests the brake needs adjustment attention?
- With the service brakes fully applied, what angle relationship should the pushrod and slack adjuster arm show?
- Why should automatic slack adjusters not be manually readjusted again and again in normal service?
- In what limited situation may a manual adjustment of an automatic slack adjuster be appropriate?
- What causes pushrod stroke to gradually increase in normal use?
- Why does the legal stroke limit vary between brake chambers?
- How are many long-stroke brake chambers identified?
- Which defect at the connection between the pushrod and the slack adjuster is unsafe?
- What can happen if the brakes on the left and right of one axle are adjusted very differently?
- What is the difference between free stroke and applied (power) stroke?
- If a brake is adjusted too tightly, what problem can result?
- A brake is manually brought back into adjustment but is out of adjustment again a few days later. What does that pattern most likely mean?
- Why should only a properly trained and qualified person adjust or repair brakes for continued service?
- What should you do if you discover a brake is beyond its pushrod stroke limit before a trip?
- When measuring stroke, why should the measurement be made with a full service brake application rather than a light touch on the pedal?
- Which condition can make a stroke reading misleading if it is not corrected first?
- What is brake fade?
- Why do overheated brake drums contribute to fade in drum brakes?
- What is the most important decision to make before starting down a long, steep grade?
- What is snub braking on a downgrade?
- Why does riding the brakes with light continuous pressure wear them out and cause fade on a mountain grade?
- What is the primary role of engine braking (including an engine retarder) on a downgrade?
- What should you do if your brakes begin to fade while descending?
- Why should you check your brakes and speed at the top of a grade, where a brake check area or pullout is provided?
- Which sign suggests your brakes are overheating on a descent?
- What can retarders do that requires caution on slippery roads?
- If you must use a truck escape (runaway) ramp, what should you expect and do?
- Why does vehicle speed matter so much when judging how hard a downgrade is on the brakes?
- After driving through deep water, brakes may be wet and weak. How can you dry them?
- What is brake lag, and how is it different from brake fade?
- Why can trying to downshift after you are already going too fast on a grade fail?
- What is a safe speed on a downgrade based on?
- How does total vehicle weight affect brake heating on a long grade?
- What should you do during a stop after a hard descent if the brakes are very hot?
- Which practice best preserves service brakes for an emergency on a long grade?
- Why should you never shift to neutral or coast down a grade to save fuel?
- What is the main job of an antilock braking system (ABS) on a truck?
- The yellow ABS malfunction lamp stays on after the startup check while you are driving. What does it mean?
- What should a tractor ABS lamp normally do when the ignition is first turned on?
- How should you brake in an emergency in a vehicle with working ABS?
- Does ABS guarantee a shorter stopping distance on every road surface?
- Why does keeping the front wheels rolling under hard braking matter so much?
- What can happen if trailer wheels lock during a hard stop without working ABS?
- What can happen if drive-axle wheels lock on a slippery surface?
- How does ABS know a wheel is about to lock up?
- A vehicle has ABS on the tractor but the trailer does not have ABS. What should the driver understand?
- Where is the ABS malfunction lamp for a trailer often located, in addition to any dash indication on equipped tractors?
- After coupling, how can a driver get a basic indication that trailer ABS power and self-check are working where the system provides a lamp check?
- What driving habit is still required even when ABS is working perfectly?
- Why should you not rely on ABS to prevent a skid when entering a curve too fast?
- Which maintenance or inspection point is specific to ABS-equipped brakes?
- If ABS fails partway through a trip, how should your braking technique change?
- On a vehicle without ABS, what is the purpose of releasing the brakes when the wheels lock during an emergency stop?
- What should you expect to feel or hear when ABS is actively controlling a hard stop on many vehicles?
- Why can using an engine retarder on a slippery road be a problem even on an ABS vehicle?
- What does an ABS lamp that comes on and stays on while driving at speed tell you about the service brakes themselves?
- Why must air tanks (reservoirs) be drained regularly?
- When should manual air tank drains normally be opened?
- What can happen if water is allowed to collect in the air system in freezing weather?
- What is the purpose of an alcohol evaporator in an air brake system?
- What maintenance does an alcohol evaporator require in winter use?
- What does an air dryer do in a modern air brake system?
- Even with an automatic air dryer or automatic drain valves, why should the driver still check the tanks?
- Finding a large amount of oil being discharged from the tanks or dryer is a sign of what?
- How is a typical manual tank drain valve operated?
- What safety points apply when you drain air tanks?
- Which tank or part of the system tends to collect the most moisture and should never be skipped when draining?
- What does the brief blast of air you may hear from beneath the cab or frame at intervals on a dryer-equipped truck usually indicate?
- A dryer that never purges, or tanks that keep filling with water despite a dryer, most likely indicates what?
- Why does alcohol in the system not excuse skipping tank draining?
- What problem can sludge and corrosion from neglected tanks cause in brake valves?
- A trailer breaks away from the tractor and tears both air lines loose. What happens on the tractor side in the first moments?
- What does the trailer air supply control (the red control in the cab) do in normal operation?
- At about what pressure will the trailer air supply control pop out (or the tractor protection valve close) as system pressure falls?
- How do you test the tractor protection valve during an inspection?
- What is the difference between the trailer's emergency (supply) air line and its service air line?
- What commonly identifies the emergency and service glad hands on a combination vehicle?
- What happens to the trailer brakes if a trailer breaks away from the tractor?
- What is the trailer hand valve (hand control) used for?
- Why should the trailer hand valve not be used to hold a parked trailer or combination?
- What is stab braking, and when is it used?
- During stab braking, when exactly should you release the brakes?
- How does controlled braking differ from stab braking?
- Why should stab braking not be used on a vehicle whose ABS is working?
- Before uncoupling a trailer, what air brake steps help keep the trailer secure?
- What should you check about glad hand seals and air lines after coupling a trailer?
- If the service and emergency lines were cross-connected, what problem could result?
- After coupling, how can you test that the trailer service brakes respond to the pedal?
- Why does a trailer need its own air tanks instead of relying only on air sent from the tractor?
- What is the risk of using the trailer hand valve while driving to correct every trailer sway or slow the combination on a grade?
- In an emergency stop without ABS, what should you do if the vehicle begins to skid because the wheels have locked?